Ralliart Exterior

[NateIRL]

Hey guys I have a Lancer 2010 ES and was looking to upgrade my exterior with ralliart bits from a wreckers. Has anyone done it before? Does it use the same clips and holes? so it can just be swapped? Or is extra modification required e.g. drill holes etc?

[Skrallex]

Extra medication?? Anyway, the RA exterior is mostly the same as that of the VRX, except the bonnet of course. You can buy the spoilers on-line or from members here who might be selling them, though you will usually have to get them resprayed to match your colour. MitsubishiParts.com is a good site to check, and if you look in the group-buy forum here you will find a thread where you can get them cheaper through Ofey, the chief buyer.

For example, here's the front spoiler/air-dam (in red, they have other colours, these ones are already painted though not sure how well the colours match).

[Ronan.Butler11]

^ thought i would give this a bump, would this still apply for the ralliart sportback and the VRX? looking at putting the RA rear bumper on my VRX so i can get a double exhaust. only aftermarket i found are $400+...

[Skrallex]

I was actually somewhat mistaken, the RA front bumper, while similar, requires a lot of different parts such as different fog lights, different undertray, etc. As for the rear bumper, I'm not really too sure, I would imagine it would fit on the same and shouldn't have anything in the way. You can get some rear diffusers that don't replace the whole rear bumper, but I imagine you would have to cut your existing bumper to put those on.

Are you dead set on a dual exhaust? They look good, but it's going to be a lot more money and work than just getting a new single exit system installed.

[Ronan.Butler11]

I'm pretty set on the dual exit, only going for an axle back so it isn't as pricey as i could be. i just feel the back end is letting the car down a bit, and love the look of dual exit. but like you said, the whole system is a bit pricey.

[Skrallex]

Yeah, it certainly looks nice with dual exit. In that case, it's been done a few times by people here on the forums, with varying success in terms of the rear bumper/diffuser. Just use the search option and you shouldn't have any problems.

Here's one thread on the Mars Performance bumper.

[Ronan.Butler11]

better look nice once it's done hahaha, reckon i could grab a RA bumper from a wreckers? heard that Mitsubishi ask for a VIN to order it, would wreckers be the same? found an evo wrecker out at riverstone, rather know before i make that trek of a run hahaha

[aspir3]

If you like the dual exhaust look you are best to make one of them a dummy pipe otherwise it's makes it hard for tuning

[sarusa]

Would a heat shield be needed for a dual exit exhaust on MY12 + CJs?

[Skrallex]

I don't imagine a wrecker would ask for a VIN haha, they don't care as long as they can sell the part

[aspir3]

Would a heat shield be needed for a dual exit exhaust on MY12 + CJs?

I highly doubt it but it depends how hot your exhaust gets and how close it is to the bumper

[Ronan.Butler11]

If you like the dual exhaust look you are best to make one of them a dummy pipe otherwise it's makes it hard for tuning

this is true... but i do a lot of early morning driving, makes it a bit obvious that one is a dummy hahahaha

[Ronan.Butler11]

I don't imagine a wrecker would ask for a VIN haha, they don't care as long as they can sell the part

Sweeeeeet
found an evo wreckers with a few RA, might check them out within the next few weeks
Thanks for your help bro

[lancer-noob]

found an evo wreckers with a few RA,

Where did you find them? I am interested to get a RA or Evo hook.

[lancerdarryl]

Hook or hood?