***** ALERT - Nominations for your new ClubCJ Committee can be made here *****

Headlight Leveling - Wiring loom

HID's, Bulb's + LED Interior and Exterior Illumination.

Moderators: Moderators, Senior Moderators

User avatar
Shaun Patterson
Lancer VRX/GTS
Lancer VRX/GTS
Posts: 381
Joined: Fri Sep 05, 2014 9:59 pm
Location: Rockhampton Australia

Headlight Leveling - Wiring loom

Postby Shaun Patterson » Sun Sep 13, 2015 7:54 pm

Hi guys i bought some oem projectors fitted with leveling motors and comes bundled with the leveling switch for an extra 150 ill add, and in my hast i overlook the fact the my ralliart doesnt have the 3 wires in the headlight connection needed for the levelling motor to function, has anyone managed to get it to work in a lancer that didnt come with the older harness?

User avatar
SEB15
Lancer Evolution
Lancer Evolution
Posts: 931
Joined: Fri Aug 19, 2011 7:31 am
Location: Ipswich, QLD Australia

Postby SEB15 » Mon Sep 14, 2015 11:57 am

following

Swerve
Lancer VR/GT
Lancer VR/GT
Posts: 262
Joined: Sun Aug 09, 2015 8:52 pm
Location: Australia

Postby Swerve » Mon Sep 14, 2015 1:01 pm

So from what I understand you only need three wires. One for the Motor Drive, one for Voltage Comparison, and one for Ground. Ground is easy enough, but the other two are where it gets tricky. You should be able to get the wire for the "Motor Drive Circuit" on Pin 5 of C-130, and the one for the "Voltage Comparison Circuit" on Pin 3 of C-131. I'm assuming these are blanked out/not available to you.

Someone correct me if I'm wrong, I believe in Australia the leveling motor will not work on Lancers as we are missing all the sensors/wiring on the car. Though you can check the back of your headlights and adjust the light output using the adjustment screws.

Sorry I'm at work I'll have a better look at home.

himynameisdaniel
Lancer Evolution
Lancer Evolution
Posts: 824
Joined: Mon Feb 14, 2011 3:58 pm
Location: Adelaide

Postby himynameisdaniel » Mon Sep 14, 2015 1:53 pm

Check the main headlight connector harness. if it has cables to all the individual connectors then everything should be plug and play.

User avatar
Shaun Patterson
Lancer VRX/GTS
Lancer VRX/GTS
Posts: 381
Joined: Fri Sep 05, 2014 9:59 pm
Location: Rockhampton Australia

Postby Shaun Patterson » Mon Sep 14, 2015 8:13 pm

thats what i mean, it has the 3 wires required for the leveling motors blanked out

User avatar
Shaun Patterson
Lancer VRX/GTS
Lancer VRX/GTS
Posts: 381
Joined: Fri Sep 05, 2014 9:59 pm
Location: Rockhampton Australia

Postby Shaun Patterson » Mon Sep 14, 2015 8:15 pm

the older lancer do have all of the wireing necesary, and in the cabin i have the loom for the switch already there just not in the engine bay

User avatar
JustinR
Site Admin
Site Admin
Posts: 1954
Joined: Sat Jan 22, 2011 6:26 pm
Location: Sutherland Shire, Sydney

Postby JustinR » Mon Sep 14, 2015 8:19 pm

Shaun Patterson wrote:Hi guys i bought some oem projectors fitted with leveling motors and comes bundled with the leveling switch for an extra 150 ill add, and in my hast i overlook the fact the my ralliart doesnt have the 3 wires in the headlight connection needed for the levelling motor to function, has anyone managed to get it to work in a lancer that didnt come with the older harness?


Are you saying the Ralliart doesn't have the three wires and the NA's do?

User avatar
Shaun Patterson
Lancer VRX/GTS
Lancer VRX/GTS
Posts: 381
Joined: Fri Sep 05, 2014 9:59 pm
Location: Rockhampton Australia

Postby Shaun Patterson » Mon Sep 14, 2015 8:22 pm

i think they all stop from my10 onwards

Swerve
Lancer VR/GT
Lancer VR/GT
Posts: 262
Joined: Sun Aug 09, 2015 8:52 pm
Location: Australia

Postby Swerve » Tue Sep 15, 2015 1:26 am

I haven't had a look was too tired after work. As far as I know in Australia most newer models of NA Lancers, RA's and the Evo GSR don't have the wiring in the engine bay. 

Some pictures of the headlights, harness and switch might help.

My advice is either use the adjustment screws on the headlights to change the level. 

Alternatively see if you can get the wired from somewhere else (ETACs?) and splice into it. As stated earlier you need will need three wires. One for Motor Drive, one for Voltage Comparison and one for Ground.

The first wire Motor Drive would just need a 12V power supply to drive the motor. Have a look on the headlight wiring loom/harness in the engine bay, one of those wires will be a constant source of 12V which you can splice into. Try Pin 2, otherwise just locate which wire is 12V or get it from another source.

Ground is pretty self explanatory.

The Voltage Comparison wire needs to be spliced into the input signal wire on the connector/loom or Pin 4? On the switch.

It's late and I could be way off the mark but that's my thoughts.

User avatar
Shaun Patterson
Lancer VRX/GTS
Lancer VRX/GTS
Posts: 381
Joined: Fri Sep 05, 2014 9:59 pm
Location: Rockhampton Australia

Postby Shaun Patterson » Tue Sep 15, 2015 8:03 am

ill get some photo, the only reason i got these lights over other was because of the levelling motor,

i will get some photos this arvo

what you have suggest sounds like a good place to start tho

User avatar
SEB15
Lancer Evolution
Lancer Evolution
Posts: 931
Joined: Fri Aug 19, 2011 7:31 am
Location: Ipswich, QLD Australia

Postby SEB15 » Wed Sep 16, 2015 7:02 am

checked mine and i do have the plug, is a 09 MY10 RA :)

Swerve
Lancer VR/GT
Lancer VR/GT
Posts: 262
Joined: Sun Aug 09, 2015 8:52 pm
Location: Australia

Postby Swerve » Wed Sep 16, 2015 8:06 am

Can you take a photo of the plug? I had an issue with a broken wire in my headlights and while in that area of then engine bay I'm 90% sure I also have the plugs if I'm thinking of the right ones.

User avatar
Shaun Patterson
Lancer VRX/GTS
Lancer VRX/GTS
Posts: 381
Joined: Fri Sep 05, 2014 9:59 pm
Location: Rockhampton Australia

Postby Shaun Patterson » Wed Sep 16, 2015 6:15 pm

i have all of the plugs just missing 3 wires on the big one

Gtrain
Lancer Learner
Lancer Learner
Posts: 3
Joined: Wed Dec 27, 2017 6:36 pm

Re: Headlight Leveling - Wiring loom

Postby Gtrain » Tue Jan 16, 2018 6:48 pm

bump on old thread but did anyone get this sorted?

User avatar
Shaun Patterson
Lancer VRX/GTS
Lancer VRX/GTS
Posts: 381
Joined: Fri Sep 05, 2014 9:59 pm
Location: Rockhampton Australia

Re: Headlight Leveling - Wiring loom

Postby Shaun Patterson » Wed Jan 17, 2018 8:36 am

Gtrain wrote:bump on old thread but did anyone get this sorted?


'
nope faqr to much effort and the oem headlights cost an arm and a leg its hardly worth it


Return to “Lighting”

Who is online

Users browsing this forum: No registered users and 61 guests