Yay got my car back. Shoutout to Northshore Mitsubishi for doing a great job, with fantastic customer service.
New transmission clutch assembly, flywheel, and new Diaqueen fluid... Now I hope that light brown oil all over the bottom plastic cover, rear of engine and transfer case is degreaser or something similarly harmless. I'd hate to think it was some essential fluid being dropped!
***** ALERT - Nominations for your new ClubCJ Committee can be made here *****
What did you do on your car today?
Moderators: Moderators, Senior Moderators
- Metalstrix
- Post Monster
- Posts: 2739
- Joined: Thu Dec 13, 2012 4:16 pm
- Location: Sydney Australia
Took a Photo of the Evo's
[img]http://www.clubcj.net/img/images/1401188433_IMG_4940[1].JPG[/img]
Then Packed away my X for the next month or SO
[img]http://www.clubcj.net/img/images/1401188604_IMG_4948[1].JPG[/img]
[img]http://www.clubcj.net/img/images/1401188705_IMG_4950[1].JPG[/img]
[img]http://www.clubcj.net/img/images/1401188433_IMG_4940[1].JPG[/img]
Then Packed away my X for the next month or SO
[img]http://www.clubcj.net/img/images/1401188604_IMG_4948[1].JPG[/img]
[img]http://www.clubcj.net/img/images/1401188705_IMG_4950[1].JPG[/img]
My EVO (X MR) progress: http://clubcj.net/viewtopic.php?p=328713#328713
4 cylinders, 3 diamonds, 2 litre, 1 turbo, 0 reasons to buy anything else
ROTM WINNER SEPT 2014
4 cylinders, 3 diamonds, 2 litre, 1 turbo, 0 reasons to buy anything else
ROTM WINNER SEPT 2014
- belle_tb_ES
- Post Monster
- Posts: 2614
- Joined: Tue May 08, 2012 11:39 am
- Location: Hills District, NSW
Installed some HIDs recently. ...made a massive difference!
PRESENT: 2015 Audi S3
PAST:2009 Lancer ES called Lancee...
Garage: http://clubcj.net/garage.php?mode=view_vehicle&CID=947
I
PAST:2009 Lancer ES called Lancee...
Garage: http://clubcj.net/garage.php?mode=view_vehicle&CID=947
I
- lantourismo
- Lancer Legend
- Posts: 1248
- Joined: Sat Apr 13, 2013 8:32 pm
- Location: Perth, Australia
megatron wrote:well not today but on the weekend [img:0604f24ba0]http://www.clubcj.net/img/images/1401697014_10425875_10202716309762179_7002506142617003409_n.jpg[/img:0604f24ba0][img:0604f24ba0]http://www.clubcj.net/img/images/1401697014_10301357_10202716520167439_3331822230662247004_n.jpg[/img:0604f24ba0][img:0604f24ba0]http://www.clubcj.net/img/images/1401697014_1780901_10202716309642176_4196651219023831608_n.jpg[/img:0604f24ba0]
Is that the piece of the space station that fell out of the sky? hehe Jk, looks good. If it wasnt for the bumper being a PITA to remove, id do mine...
wound the coils for an extra 2 cm drop each side, need to clean the rear drivers side coil thread though
after i do that ill just max them out, not much left in them and still plenty of height to go down
after i do that ill just max them out, not much left in them and still plenty of height to go down
My Build Thread : http://clubcj.net/viewtopic.php?t=14731
ROTM Winner OCTOBER 2015 (Nominated for favourite CJ)
-Australia's first airbagged CJ-
ROTM Winner OCTOBER 2015 (Nominated for favourite CJ)
-Australia's first airbagged CJ-
- TasteTheRuss
- Lancer Newbie
- Posts: 73
- Joined: Sat Feb 01, 2014 6:40 pm
- Location: Sydney, Australia
Finally saved up enough to get some coils, so finally got my baby lowered
Only around 40 at the back and 35 at the front. Didn't want to go too low as I'm not the only one that drives the car and a couple of em don't notice bumps haha
[img]http://www.clubcj.net/img/images/20140603123906_IMG_0225[1].JPG[/img]
Only around 40 at the back and 35 at the front. Didn't want to go too low as I'm not the only one that drives the car and a couple of em don't notice bumps haha
[img]http://www.clubcj.net/img/images/20140603123906_IMG_0225[1].JPG[/img]
- cadburyyum
- Lancer ES/EX
- Posts: 131
- Joined: Fri May 30, 2014 10:24 pm
- Location: Sydney, Australia
Who is online
Users browsing this forum: No registered users and 193 guests