***** ALERT - Nominations for your new ClubCJ Committee can be made here *****

Tiff's adventure with Plasti Dip!

Exterior Parts/Accessories & Modifications.

Moderators: Moderators, Senior Moderators

User avatar
Mystique
Lancer MASTER
Lancer MASTER
Posts: 1729
Joined: Mon Sep 30, 2013 8:28 pm
Location: Launceston, Tasmania, Australia

Tiff's adventure with Plasti Dip!

Postby Mystique » Sat Nov 30, 2013 2:25 pm

I had a small adventure today with Plasti Dip.. Oh Plasti Dip.. You are simply fantastic... except I screwed it up :P Was happy with the finished product and then I didn't like it so i pulled it off all xD Decided it's going to be easier to get it vinyl wrapped :S and I didn't like the chrome with it either ;S

But...

Without number plate! Am very hesitant to put it back on :(

Image

All Taped up :P haha.. I went overboard but I wanted to be safe then sorry....
Image

First coat:

Image

After a few more coats, it was the finished product after pulling the Newspaper and tape off... and well.... I ended up pulling it all off, I just need to get a knife and scrape the rest off >_< The masking I did was a lil uhh :S Horrible because it started pulling the rest of the plasti dip off with it... and this is how it ended up :P

Image

and after pulling the plasti dip off, the only thing it really stuck to was the white spot that's on my front bumper :S I guess it looks like she has a beauty spot or something lol.... But in saying that, I think I'm going to just get it vinyl wrapped and the chrome removed :S I didn't like how it turned out xD it looked like my car had a mustache... :S

Image
Daily: My14 Lancer LX
Weekender: 2009 MY09 Ralliart Hatch

Image
My Mod Thread: viewtopic.php?p=324612#324612
Instagram: http://instagram.com/mitsii_lx

User avatar
vermilioN
Lancer Ralliart
Lancer Ralliart
Posts: 632
Joined: Sat Jun 16, 2012 1:06 pm
Location: Adelaide

Postby vermilioN » Sat Nov 30, 2013 2:30 pm

dat beauty spot.
Image

Australia's sexiest blacked out ralliart ;)

evo x turbo, ets intercooler, turbosmart wga, aem intake, ur intercooler piping, ur turbo back exhaust, 3port

User avatar
Mystique
Lancer MASTER
Lancer MASTER
Posts: 1729
Joined: Mon Sep 30, 2013 8:28 pm
Location: Launceston, Tasmania, Australia

Postby Mystique » Sat Nov 30, 2013 2:31 pm

Ikr? >_<

Definitely getting it vinyl wrapped... or may give it another go next weekend... but I'm not feeling that spontaneous now xD
Daily: My14 Lancer LX
Weekender: 2009 MY09 Ralliart Hatch

Image
My Mod Thread: viewtopic.php?p=324612#324612
Instagram: http://instagram.com/mitsii_lx

User avatar
sleeper
Alumni
Alumni
Posts: 8259
Joined: Fri Apr 23, 2010 10:14 am
Location: brisbane
Contact:

Postby sleeper » Sat Nov 30, 2013 2:49 pm

strange tiff, i dont know what went wrong there, u did everything right :(

maybe the grille was waxed or something, just guessing.

normally its a piece of cake
210 KWATW 400nm RALLIART Virtual Dyno 1/1
http://goo.gl/GrUosm


Image

User avatar
Metalstrix
Post Monster
Post Monster
Posts: 2739
Joined: Thu Dec 13, 2012 4:16 pm
Location: Sydney Australia

Postby Metalstrix » Sat Nov 30, 2013 2:58 pm

it looked alright! lol
They will learn... I will always be a step ahead

No longer an active member.

User avatar
D
Lancer Evolution
Lancer Evolution
Posts: 989
Joined: Sat Sep 07, 2013 3:01 pm
Location: SA, Australia

Postby D » Sat Nov 30, 2013 3:21 pm

Did you let it dry fully?, because that may be your issue, if you peel the masking off straight after you spray the last coat (whilst it is still wet), you will get nice smooth edges and the dip will stay where as if you peel it once dry it will take the rest with it as it has already bonded together thus the whole strip will come off, hope this helps
My EVO (X MR) progress: http://clubcj.net/viewtopic.php?p=328713#328713
4 cylinders, 3 diamonds, 2 litre, 1 turbo, 0 reasons to buy anything else
Image
ROTM WINNER SEPT 2014

User avatar
Mystique
Lancer MASTER
Lancer MASTER
Posts: 1729
Joined: Mon Sep 30, 2013 8:28 pm
Location: Launceston, Tasmania, Australia

Postby Mystique » Sat Nov 30, 2013 3:32 pm

I took it off after the did the last coat :)
Daily: My14 Lancer LX
Weekender: 2009 MY09 Ralliart Hatch

Image
My Mod Thread: viewtopic.php?p=324612#324612
Instagram: http://instagram.com/mitsii_lx

User avatar
Mystique
Lancer MASTER
Lancer MASTER
Posts: 1729
Joined: Mon Sep 30, 2013 8:28 pm
Location: Launceston, Tasmania, Australia

Postby Mystique » Sat Nov 30, 2013 3:33 pm

I'm going to leave it :P and try again next weekend >_< might've been because I used the xpack car wash stuff when I washed the front bumper before doing it >____<

:S
Daily: My14 Lancer LX
Weekender: 2009 MY09 Ralliart Hatch

Image
My Mod Thread: viewtopic.php?p=324612#324612
Instagram: http://instagram.com/mitsii_lx

Luke
Lancer ES/EX
Lancer ES/EX
Posts: 166
Joined: Mon Aug 12, 2013 6:19 pm
Location: Blue Mountains, NSW

Postby Luke » Sat Nov 30, 2013 9:45 pm

I was following the whole shabang on Instagram, thank's Tiff ahaha

It may look better RA style ;) with the chrome above and below blacked out and some chrome 'tape' stuff around it?

http://www.ebay.com.au/itm/10mm-Chrome- ... 856&_uhb=1


it could either look reallllly bad or realllly good aha
just a thought :)

User avatar
Frosty
Lancer ES/EX
Lancer ES/EX
Posts: 179
Joined: Wed Jul 11, 2012 5:44 pm
Location: Sydney, NSW

Postby Frosty » Sat Nov 30, 2013 10:01 pm

The trick is to remove the tape after each coat while the plasti-dip is still wet and re-apply new tape (in the exact same location) for the next coat. Otherwise you will run into the problem you experienced >.<
Also, wash the surface with wax and grease remover before spraying, some car washes include a wax which will stop the plasti-dip from sticking.
Happy dipping! :)
2.0L - K&N Typhoon SRI - High-Flow Exhaust System - Merlinised

User avatar
Mystique
Lancer MASTER
Lancer MASTER
Posts: 1729
Joined: Mon Sep 30, 2013 8:28 pm
Location: Launceston, Tasmania, Australia

Postby Mystique » Sun Dec 01, 2013 12:20 am

Haha sorry Luke for all the posts on Instagram ;) thought I'd keep people updated haha! :P


Oooh! Thanks for the tip :3 shall keep it in mind when I try again! Am thinking that the chrome needs to go :3 although I do like it with how it is normally >_< but gah! XD
Daily: My14 Lancer LX
Weekender: 2009 MY09 Ralliart Hatch

Image
My Mod Thread: viewtopic.php?p=324612#324612
Instagram: http://instagram.com/mitsii_lx

User avatar
Kal777
Lancer VRX/GTS
Lancer VRX/GTS
Posts: 404
Joined: Mon May 21, 2012 9:48 pm
Location: Adelaide

Postby Kal777 » Sun Dec 01, 2013 10:37 am

Wax and grease remover will get any overspray off the car and neaten up the edges.
Image
Injen Cold Air Intake/K&N Invert Pod/BC BR Coilovers/Whiteline Strut Brace/DrIft Blade seats/Penrite HPR5/Penrite ProGear/PBR Gold Dot

User avatar
RallyNut
Lancer Newbie
Lancer Newbie
Posts: 44
Joined: Thu Nov 21, 2013 12:59 pm
Location: Sydney

Postby RallyNut » Sun Dec 01, 2013 11:57 am

What i found with plastic dip is that you dont want it to dry up fully between each spray i only waited like 2-3min between each spray.
it worked for me...
pepople told me to do the tape after each spray as well, im sure it should go well, but im just dont have the patience for that.. ;P
maybe give it a shot.

User avatar
Mystique
Lancer MASTER
Lancer MASTER
Posts: 1729
Joined: Mon Sep 30, 2013 8:28 pm
Location: Launceston, Tasmania, Australia

Postby Mystique » Sun Dec 01, 2013 12:11 pm

I left it 10-15 between each coat :P


Will keep that in mind next time though >_<


Am definitely thankful for all the tips guys! :) Especially the ClubCJ Vic guys on Facebook :)

Especially Damir who's been following me on Instagram and giving out advice as well :P I really appreciate it everyone!! :)


I'm definitely going to be removing the chrome and spraying that as well :P I'm going to have to do a search on here how to remove the front bumper though haha :P Although for a first timer, I am proud of how it turned out :P It could've been alot worse :P haha, I was honestly scared of doing it :P Because I've never ever done anything like this before xD but, anyway :P
Daily: My14 Lancer LX
Weekender: 2009 MY09 Ralliart Hatch

Image
My Mod Thread: viewtopic.php?p=324612#324612
Instagram: http://instagram.com/mitsii_lx

JoelT
Lancer Learner
Lancer Learner
Posts: 18
Joined: Fri Aug 30, 2013 1:33 am
Location: Australia perth

Postby JoelT » Sun Dec 01, 2013 10:29 pm

if you dont want the chrome why dont you plastidip the whole front bumper including the chrome?
surely that would be easier than taking the chrome strip off etc


Return to “Exterior”

Who is online

Users browsing this forum: No registered users and 11 guests