***** ALERT - Nominations for your new ClubCJ Committee can be made here *****

Boost gauge install

Lancer Interior Modifications.

Moderators: Moderators, Senior Moderators

Post Reply
User avatar
vermilioN
Lancer Ralliart
Lancer Ralliart
Posts: 632
Joined: Sat Jun 16, 2012 1:06 pm
Location: Adelaide

Boost gauge install

Postby vermilioN » Sat Dec 15, 2012 3:32 pm

Trying to install my mechanical Boost gauge but I cant figure out where is a good place for the hose to go through the firewall.. No idea what im doing! I want the gauge to sit on my dash on the right of my steering wheel.
Image

Australia's sexiest blacked out ralliart ;)

evo x turbo, ets intercooler, turbosmart wga, aem intake, ur intercooler piping, ur turbo back exhaust, 3port
User avatar
SAM-24A
Alumni
Alumni
Posts: 2921
Joined: Sun May 17, 2009 4:40 pm
Location: Sydney NSW

Postby SAM-24A » Sat Dec 15, 2012 3:49 pm

Mitch ... you say
"No idea what im doing!"
.... *noidea*

You really should plan & research such mods with other members who have done similar before you attempt them.
It helps prevent any unnecessary & unexpected dilemmas that might occur part way through the job .... :roll:

Try-It next time .... :wink:



Sam ..... *thumb*
Merlinised MIVEC - AspiRe 2.4L
Merlin Inspired Variable Engine Control
User avatar
Speedie
Lancer MASTER
Lancer MASTER
Posts: 1751
Joined: Thu Mar 05, 2009 11:42 pm
Location: Brisbane, QLD, Australia

Postby Speedie » Sat Dec 15, 2012 3:51 pm

I used the grommets behind the front wheels that go into the chassis rail then out by the kick panels
Image

[Evo X Brembos] [Evo X Intercooler] [Evo X UICP]
User avatar
Speedie
Lancer MASTER
Lancer MASTER
Posts: 1751
Joined: Thu Mar 05, 2009 11:42 pm
Location: Brisbane, QLD, Australia

Postby Speedie » Sat Dec 15, 2012 4:01 pm

Or you've got the one by the ABS unit behind the air box
Image



[Evo X Brembos] [Evo X Intercooler] [Evo X UICP]
User avatar
sleeper
Alumni
Alumni
Posts: 8259
Joined: Fri Apr 23, 2010 10:14 am
Location: brisbane
Contact:
Contact sleeper

Postby sleeper » Sat Dec 15, 2012 4:19 pm

i drilled a hole in the firewall then up through the A pillar

Image
210 KWATW 400nm RALLIART Virtual Dyno 1/1
http://goo.gl/GrUosm


Image
User avatar
bunnishiwa
Lancer Legend
Lancer Legend
Posts: 1284
Joined: Thu Dec 24, 2009 4:22 pm
Location: Rye, Melbourne

Postby bunnishiwa » Sat Dec 15, 2012 4:23 pm

Drilled a hole.... Brave man.

If you pull the carpet behind the accelerator pedal away you will see a grommet that goes into engine bay. Cut appropriate hole in grommet, feed tube through, put grommet back in (i used flat head screw driver). Feed tube to wherever and use cable ties in engine bay
- Self tuned - work in progress - tune revision #16_03
- GS 3 port controlled wooooot :)
- Lowered on Kings
- Black Evo X FMIC/ Evo IX BOV/ Depo HFC/ UR UICP
- Awesome self installed Alpine/JL Audio sound system
- Whiteline Rear Swaybar



Noli Timere Messorem
User avatar
sleeper
Alumni
Alumni
Posts: 8259
Joined: Fri Apr 23, 2010 10:14 am
Location: brisbane
Contact:
Contact sleeper

Postby sleeper » Sat Dec 15, 2012 4:27 pm

no not brave, i checked the brake reserviour wasnt behind it :P
210 KWATW 400nm RALLIART Virtual Dyno 1/1

http://goo.gl/GrUosm





Image
User avatar
rokpapaziz
Lancer Legend
Lancer Legend
Posts: 1344
Joined: Sat Aug 13, 2011 12:18 am
Location: Brisbane

here

Postby rokpapaziz » Sun Dec 16, 2012 6:57 am

You can try here. Not sure if yours will have the lining that covers that area. Mine doesn't.

Image[b]
Post Reply

Return to “Interior”

Who is online

Users browsing this forum: No registered users and 75 guests