Installation of Angel Eyes Help

[stirjo]

Heyo

Alright, so ive asked around, spent some days tinkering, and no luck with my angel eyes. DIY i can do but all the electrical i get lost on. I know i should probably go to an electrician to do this, but i bought my lancer and love it and appreciate it, and it would mean heaps to me if i can do all the mods myself. This is where you come in!

I cant really write the problems im having so i went out this morning and took some shots. All i need is a clear description on installing the AutoMoGlow Angel eyes to my lancer 2011 CJ.



Anyways heres my engine




And heres the angel eyes





What i need to know is where all the connections go


This is the balast im assuming, which i just cable tie to anything




Im not sure where this goes coz the orange tab fits perfectly in a spot in the fuse box




Positive and grounding connections



Which goes in these areas yeah?????




I have absoluuuuuuuutely no clew what this is and where it goes (theres a yellow one and a white one)




These are connect correctly yeah???




And finally what do i connect here to make the angel lights act as DRLs??





Sorry if that sounds stupid, but you all own lancers, you probably know what i mean XD
If you could find the time out of your busy schedule to help a brother in need that'd be perfect

Cheers

Jordan

[Dirtee]

If you want them to be DRL's i'd assume you just connect them to a point which is always active when the ignition is on, say one of the fuses in the fuse box - a test light will help.

Where did you buy these from?

[stirjo]

automoglow online store, ill try that though thanks

[Chubb]

If you hook the positive up to the battery the light will be on ALL the time as in they will only turn off when the battery runs flat.

You have said you have no idea what you are doing, all I can do is issue this warning be very very very careful as to what you are doing in relation to wiring. Don't you think a good start would be to actually install the DRL/angel eyes in the headlight as that is the most complicated and time consuming job.

[Speedie]

Have you got your lights open?

[Glenn]

Should have two wires fro me the actual angel eyes going to some sort of but I'm guessing you have the led ones. The thing in your picture looks more like a relay which would explain the yellow wire your not sure of. Again cant say for sure but that yellow one is most likely the signal wire so even if you have it all wired up positive and ground, nothing will happen unless you send a signal to the yellow wire. Try hooking it up to a positive acc source as a test. Then when you do the hard part and open your lights you can then wire it to something like your low beam

[stirjo]

yeah sweet sweet ill try that, Glenn.

Yeah i spent today, and seperated the headlights, oven was to small so used Gods 39 degrees he gave us and my hair dryer to open haha

Yeap its all ready to go, drilled a littl whole in the back and filled it up, so anymore thoughts guys??

Cheers

[stirjo]

alright its all kinda done, i know what all the parts are, 3m's sticking it to my headlights, what do i do if i want them to come on INSTEAD of the parking lights????

Cheers for all the help

[T-All3NT]

don't take my word on this cause i haven't done anything of the sort, in my head with limited knowledge of car electrics this should work

if you connect the angel eyes to the parking light wires, and remove the parkers, it should turn on, the only thing is whether there is enough powers in the parkers to have the eyes shine/shine as bright as you want

[Speedie]

I'd be using these http://www.ebay.com.au/itm/10x-T10-168- ... 1c1a257bb4 and wiring in the relay to it so you don't have to damage the factory wiring

[T-All3NT]

Id be using these http://www.ebay.com.au/itm/10x-T10-168- ... 1c1a257bb4 and wiring in the relay to it so you dont have to damage the factory wiring

that will be a better way, didnt even think of that

[stirjo]

alright thanks for that tim and dan, ill see how that works

cheers