***** ALERT - Nominations for your new ClubCJ Committee can be made here *****

Draining coolant and refilling in CJ 2.0 litre

Servicing, Oil Changes, Fluids & Much More.

Moderators: Moderators, Senior Moderators

brislancer
Lancer Newbie
Lancer Newbie
Posts: 24
Joined: Wed Sep 09, 2009 2:43 pm
Location: Brisbane

Draining coolant and refilling in CJ 2.0 litre

Postby brislancer » Thu Jul 15, 2010 7:52 pm

Looking at doing a coolant change and refill on my ES 2.0. Looks like there is a butterfly shaped bung on the radiator, but was wondering if anyone had done a coolant change on their car. Am asking if anyone knows if there any bleeder screws in the head or block to undo for air release when refilling system?

Any help much appreciated!!!

smithsy
Lancer VR/GT
Lancer VR/GT
Posts: 252
Joined: Wed Jan 27, 2010 8:54 am
Location: West side

Postby smithsy » Thu Jul 15, 2010 8:04 pm

Pretty sure there aren't any bleeder screws, just use the butterfly one and then remove the hose at the end.

You do need to make sure the coolant is up to temp though so that the thermostat is open

User avatar
Mizta B
Alumni
Alumni
Posts: 5867
Joined: Sun Dec 21, 2008 8:29 am
Location: Mortdale, NSW, Australia

Postby Mizta B » Thu Jul 15, 2010 9:10 pm

When we did LZY_EYE's car we only used the butterfly bleeder on the radiator and had no problems with air pockets
Australasian Gerbil Rearers Organisation, Official Re-Seller.
Image
MY09 Rally Red VRX ClubCJ's 1st 4B12 2.4L - CCJ Lifetime Member #0004.
Merlinised....

brislancer
Lancer Newbie
Lancer Newbie
Posts: 24
Joined: Wed Sep 09, 2009 2:43 pm
Location: Brisbane

Postby brislancer » Fri Jul 16, 2010 1:22 pm

Ok thanks guys for your input, sounds straight forward then....

User avatar
DJBOOBY
Lancer ES/EX
Lancer ES/EX
Posts: 119
Joined: Sat Oct 03, 2009 8:10 pm
Location: Tumut NSW Australia

Postby DJBOOBY » Fri Jul 16, 2010 2:28 pm

check that coolent will suit a lancer some coolants are diff
eg some commodores had a problem with welsh plug been eaten away by some coolants.
Ask a dealer
Image

brislancer
Lancer Newbie
Lancer Newbie
Posts: 24
Joined: Wed Sep 09, 2009 2:43 pm
Location: Brisbane

Postby brislancer » Sat Jul 17, 2010 6:52 am

No probs there, have the genuine Mitsubishi coolant to use.

simonbrownxw
Lancer Learner
Lancer Learner
Posts: 3
Joined: Mon May 01, 2017 4:44 am

Re: Draining coolant and refilling in CJ 2.0 litre

Postby simonbrownxw » Sat May 13, 2017 4:09 pm

just tried to drain coolant in my CJ VRX up to running temp undone butterfly screw only 3.5 litres came out should be about 6 something as I like to do things properly hopped underneath car there is a bung under exhaust MANIFOLD allen key I hope it is had enough do it tomorrow hope that works already wasted $30 in coolant.

Falcoon
Lancer Learner
Lancer Learner
Posts: 10
Joined: Thu Feb 18, 2016 11:20 am
Location: Brisbane, Australia

Re: Draining coolant and refilling in CJ 2.0 litre

Postby Falcoon » Mon May 29, 2017 7:14 pm

Might be a silly question but opening the drain plug whilst hot and under pressure would seem problematic. Did you wait for it to cool somewhat or take some special precautions?
Without knowing the interior of the engine, if the drain plug is at the lowest point of the cooling system, I would expect the coolant to drain from both sides of the thermostat, even if it were closed. Can anyone confirm or dispute this?

User avatar
sarusa
Lancer Legend
Lancer Legend
Posts: 1287
Joined: Fri Sep 04, 2015 3:22 pm
Location: melbourne

Re: Draining coolant and refilling in CJ 2.0 litre

Postby sarusa » Tue May 30, 2017 9:17 am

If you are leaving half the old coolant in the car make sure the added coolant is the same, or could have problems. Its unwise to mix coolants!


Return to “Maintenance”

Who is online

Users browsing this forum: No registered users and 79 guests