ClubCJ - The CJ Lancer Club

ITEM: Greddy SE Exhaust & K&N Panel Filter for 2.0lt CVT or equivalent

LOCATION: Bankstown, Sydney NSW

ITEM CONDITION: Greddy has been used for about 3 months. Good condition overall.
K&N Filter has been used for about 300 km. Looks like new.

REASON FOR SELLING: Greddy exhaust doesn't fit my piping system with the Super Circuit headers on. Sticking with stock filters instead of the K&N.

PRICE AND PAYMENT CONDITIONS: Open to all reasonable offers. Would honestly like to recover $400+
Cash on pick-up is probably the best.

SHIPPING AND POSTAL ARRANGEMENTS: Pick up from Civic Tower at Bankstown during working hours.

EXTRA INFO: Greddy exhaust is not supplied with bolts or nuts. Refer to the Greddy How-To for instructions and correct-sized bolts

If you look at the third photo, you can see a smudge effect. I can't seem to wipe it out. I never noticed it until taking the photos today, and I don't want to try to get it off. Other than that, the exhaust is OK for 3 months of usage.

CONTACT INFO: ClubCJ PM for now.

PICTURES:

Hey man ... Is a Greddy SE incompatible with SuperCircuit headers in all cases, or was this something specific to your setup?

I suspect it's specific only to danny's car.

I have both and everything is fine in my case.

However Danny had issues with a knocking noise I recall. The GReddy in all cases gets pushed back by a few mm, so the rubber rungs angle back so the exhaust doesn\'t hang as low as it used to. This is just an observation, and it may or may not be the cause of Danny\'s knocking sound.

My personal observation on my own car is that the exhaust does gurgle or pop more noticeably with the headers installed during the off throttle if I 'blip' it when down shifting. This from the inside of the car with the windows up sounds like a knock noise.

Danny's exhaust is fine and would be a great buy for anyone interested and it's his choice to sell if he wishes to as he hasn't had luck with his current setup. Best of luck on the sale!

Yeah I think the fitting issue was for my car only, as there are many others who have tried the Greddy SE + Super Circuit header combo without apparent problems.

I had the rubber rung flex when I had the Greddy one which, although it didn't look right, it didn't cause any knocking issues. It was when I had the headers put in that the mid-piping got pushed up and was knocking against the fuel tank heat shield.

With the headers on by itself, I've noticed that the "tinny" sound from the engine is more pronounced, but that's about it.

Anyway, I'll get some photos up after some food.

Well it's a good price. I have a Greddy and recommend it. Good luck with the sale dude.

To help this sale out I am in Sydney this weekend for the NSW meet then next weekend I will be in Brisbane. So if it suits Danny I could meet up with him to pick up the exhaust and bring it to brisbane with me. So anyone in Ipswich, Brisbane, Gold coast interested in a Greddy this a damn good price I paid near $700 for mine and I love it :D.

***Note this Greddy system will fit the 2.0l and 2.4l NA lancer both CVT and Manual same with the K&N filter.

I'm putting priority up for those who can pick it up from my workplace. Otherwise, I'll need to consider those who can't or are interstate.

PM'ed LOL I work 10mins away from Bankstown

Edit: Oh and if the price is right Ill buy it off you today. Haha

Hi guys,

SPRKLS will be buying the exhaust and filter off me.

Thanks for your enquiries guys.

Sorry just SC but SPRKLS had provided their interest before, so I had to prioritise it based on that.

Cheers,
Danny

haha no problem ^^

Hey everyone,

hey dannyboi,
I'm just curious, but where did you buy the GReddy SE exhaust from in Australia anyways?
'Because I'm looking to buy one soon and I would like to buy it hopefully from a site/store in Australia.
But if not I would still like to know the site you used (if used) to buy the exhaust.

Most members have had theirs shipped from overseas. As far as I know, there is no one that stocks these in Australia to date.