Blanka's angel eyes
Posted: Sat Mar 21, 2009 8:21 am
ok peoples finally my camera and my internet is in one place so that means that i can now upload some pics of my angel eyes. i had installed them a few weeks ago but due to my camera being down innisfail low on battery and my charger up cairns i couldnt take any pics*note my camera is not the best but it will do lolz*
installing took about 3 1/2 hours lucky i did it in the morning cos it got really hot towards 12 noon lolz. Installation guide can be found here http://clubcj.net/viewtopic.php?t=572
i basiclly followed the instructions was pretty easy, first remove the front bumber, just some screws and clips then it comes off, then remove the 3 screws thats holding the headlight to the car n walla headlights comes out *remember to take all the bulbs out first*
was a bit scared of baking the headlights in the oven at first but it turned out ok set oven to 100 degrees n put light in for 5 mins. After that it should come apart pretty easy, just undo the clips.* i got a scissor to help me cut the glue a bit but once the headlight is opened its all smooth sailing there.
Resealing is just as simple put the headlight bak together n bake it for 5 min at 100 degrees then push hard on it n make sure u get all the clips to clip in.
I did find that my lights were a bit off when i was driving at night so i had to adjust them, easy process heres link http://clubcj.net/viewtopic.php?t=118
ok the high beam ring *which is the little one fits perfectly but the low beam does not so its out a bit just fiddle with it untill u think u got it best as u could.
as u can see on this image if u look closely at the big ring u can see it is not sitting perfectly but thats the best i got it
here r some pics i took last night n this morning *note i drove from cairns to innisfail last night so my car has alot of dead bugs on it havent washed it yet*
on wiring i wired the angel eyes to the little light on the side of the headlight so it always comes on when i turn the lights on
they look very sexy lolz my cousin owns a ch lancer n he wants to order these rings lolz. Thanks to Eric at AutomoGlow for the installation guide it really helped
installing took about 3 1/2 hours lucky i did it in the morning cos it got really hot towards 12 noon lolz. Installation guide can be found here http://clubcj.net/viewtopic.php?t=572
i basiclly followed the instructions was pretty easy, first remove the front bumber, just some screws and clips then it comes off, then remove the 3 screws thats holding the headlight to the car n walla headlights comes out *remember to take all the bulbs out first*
was a bit scared of baking the headlights in the oven at first but it turned out ok set oven to 100 degrees n put light in for 5 mins. After that it should come apart pretty easy, just undo the clips.* i got a scissor to help me cut the glue a bit but once the headlight is opened its all smooth sailing there.
Resealing is just as simple put the headlight bak together n bake it for 5 min at 100 degrees then push hard on it n make sure u get all the clips to clip in.
I did find that my lights were a bit off when i was driving at night so i had to adjust them, easy process heres link http://clubcj.net/viewtopic.php?t=118
ok the high beam ring *which is the little one fits perfectly but the low beam does not so its out a bit just fiddle with it untill u think u got it best as u could.
as u can see on this image if u look closely at the big ring u can see it is not sitting perfectly but thats the best i got it
here r some pics i took last night n this morning *note i drove from cairns to innisfail last night so my car has alot of dead bugs on it havent washed it yet*
on wiring i wired the angel eyes to the little light on the side of the headlight so it always comes on when i turn the lights on
they look very sexy lolz my cousin owns a ch lancer n he wants to order these rings lolz. Thanks to Eric at AutomoGlow for the installation guide it really helped
