***** ALERT - Nominations for your new ClubCJ Committee can be made here *****

Blanka's angel eyes

HID's, Bulb's + LED Interior and Exterior Illumination.

Moderators: Moderators, Senior Moderators

User avatar
blanka
INACTIVE Member Account
Posts: 822
Joined: Wed Sep 03, 2008 9:47 pm
Location: Cairns, QLD, Australia

Blanka's angel eyes

Postby blanka » Sat Mar 21, 2009 8:21 am

ok peoples finally my camera and my internet is in one place so that means that i can now upload some pics of my angel eyes. i had installed them a few weeks ago but due to my camera being down innisfail low on battery and my charger up cairns i couldnt take any pics*note my camera is not the best but it will do lolz*

installing took about 3 1/2 hours lucky i did it in the morning cos it got really hot towards 12 noon lolz. Installation guide can be found here http://clubcj.net/viewtopic.php?t=572

i basiclly followed the instructions was pretty easy, first remove the front bumber, just some screws and clips then it comes off, then remove the 3 screws thats holding the headlight to the car n walla headlights comes out *remember to take all the bulbs out first*

was a bit scared of baking the headlights in the oven at first but it turned out ok set oven to 100 degrees n put light in for 5 mins. After that it should come apart pretty easy, just undo the clips.* i got a scissor to help me cut the glue a bit but once the headlight is opened its all smooth sailing there.

Resealing is just as simple put the headlight bak together n bake it for 5 min at 100 degrees then push hard on it n make sure u get all the clips to clip in.

I did find that my lights were a bit off when i was driving at night so i had to adjust them, easy process heres link http://clubcj.net/viewtopic.php?t=118

ok the high beam ring *which is the little one fits perfectly but the low beam does not so its out a bit just fiddle with it untill u think u got it best as u could.
Image
as u can see on this image if u look closely at the big ring u can see it is not sitting perfectly but thats the best i got it

here r some pics i took last night n this morning *note i drove from cairns to innisfail last night so my car has alot of dead bugs on it havent washed it yet*
Image
Image
Image
Image
Image
Image

on wiring i wired the angel eyes to the little light on the side of the headlight so it always comes on when i turn the lights on
Image


they look very sexy lolz my cousin owns a ch lancer n he wants to order these rings lolz. Thanks to Eric at AutomoGlow for the installation guide it really helped
Last edited by blanka on Sat Mar 21, 2009 9:37 am, edited 2 times in total.

User avatar
SkitZaY
INACTIVE Member Account
Posts: 97
Joined: Wed Mar 18, 2009 5:52 pm
Location: NSW, Australia

Postby SkitZaY » Sat Mar 21, 2009 8:36 am

Now that's a detailed post.

End results looks heaps good man, envy.
Image

User avatar
blanka
INACTIVE Member Account
Posts: 822
Joined: Wed Sep 03, 2008 9:47 pm
Location: Cairns, QLD, Australia

Postby blanka » Sat Mar 21, 2009 8:37 am

ahah thanks dude didnt have my camera with me when i was installing so dont have any pics of when i was pulling my car apart
Uchiha Itachi
Image

User avatar
Panther4B11
INACTIVE Member Account
Posts: 342
Joined: Thu Dec 18, 2008 11:22 pm
Location: Brisbane, QLD, Australia

Postby Panther4B11 » Sat Mar 21, 2009 8:52 am

I really like them. I would do it to but i WILL more then likely break something. lol.
Image

User avatar
Ozie
INACTIVE Member Account
Posts: 5445
Joined: Mon Sep 22, 2008 7:00 am
Location: Sydney, NSW, Australia

Postby Ozie » Sat Mar 21, 2009 8:54 am

they do look good!
i might have to get some...

User avatar
Tarquin
Lancer Legend
Lancer Legend
Posts: 1015
Joined: Wed Sep 03, 2008 8:54 am
Location: BrisVegas, QLD, Australia

Postby Tarquin » Sat Mar 21, 2009 6:04 pm

blanka wrote:on wiring i wired the angel eyes to the little light on the side of the headlight so it always comes on when i turn the lights on


What I'm planning to do also....

Nice Blanka - thanks for the write up and piccies.... ** My turn next... :wink:

Hey - Did you need to drill a hole for the cables? or rather, how did you thread the cables out of the headlight housing....?

And - did you Sicone seal yours down onto the rings, or just use the stickie pads....?

I might have to try and get mine sorted out soon....
Last edited by Tarquin on Sat Mar 21, 2009 7:54 pm, edited 2 times in total.
- CCJ Premium Member #0015.
Image
Tarq's Paintshop

User avatar
Speedie
Lancer MASTER
Lancer MASTER
Posts: 1751
Joined: Thu Mar 05, 2009 11:42 pm
Location: Brisbane, QLD, Australia

Postby Speedie » Sat Mar 21, 2009 6:25 pm

Looking good.
Image

[Evo X Brembos] [Evo X Intercooler] [Evo X UICP]

User avatar
777_AJB
INACTIVE Member Account
Posts: 341
Joined: Thu Feb 26, 2009 8:34 pm
Location: Brisbane, QLD, Australia

Postby 777_AJB » Sat Mar 21, 2009 6:41 pm

cool nice job
Image

User avatar
blanka
INACTIVE Member Account
Posts: 822
Joined: Wed Sep 03, 2008 9:47 pm
Location: Cairns, QLD, Australia

Postby blanka » Sat Mar 21, 2009 7:21 pm

no i just treaded them through the headlights didnt drill anything and i just used the stick pads they look pretty secure so yea lolz[/quote]

User avatar
Phoenix
INACTIVE Member Account
Posts: 426
Joined: Thu Nov 20, 2008 9:34 pm
Location: Parramatta, NSW, Australia
Contact:

Postby Phoenix » Sat Mar 21, 2009 8:20 pm

good stuff blanka, they look good!
Mah Ride: 2006 Hyundai Getz + 08 Lancer Bodykit

User avatar
m1n1on
Lancer VRX/GTS
Lancer VRX/GTS
Posts: 410
Joined: Sun Dec 28, 2008 10:46 am
Location: Melbourne, VIC, Australia

Postby m1n1on » Sat Mar 21, 2009 8:50 pm

nice!

thanks blanka for the writeup... still very tempting :)

User avatar
asHxP
Lancer VR/GT
Lancer VR/GT
Posts: 204
Joined: Wed Mar 18, 2009 5:48 pm
Location: Sydney, NSW, Australia

Postby asHxP » Wed Mar 25, 2009 3:36 pm

Very nice.. no fog up yet?? Are they bright enough to light the road at dark night?

User avatar
blanka
INACTIVE Member Account
Posts: 822
Joined: Wed Sep 03, 2008 9:47 pm
Location: Cairns, QLD, Australia

Postby blanka » Wed Mar 25, 2009 4:25 pm

asHXP wrote:Very nice.. no fog up yet?? Are they bright enough to light the road at dark night?


yeh they r, i had to adjust the headlights after putting the rings on, but yeh i can see where im going lolz, n on fog lights, i want to get a pair but want body kit first lolz

User avatar
Josh_Emerton
Lancer MASTER
Lancer MASTER
Posts: 1920
Joined: Fri Oct 17, 2008 10:49 pm
Location: Cairns, QLD, Australia

Postby Josh_Emerton » Wed Mar 25, 2009 4:25 pm

They look great Zeb

I'd do it myself but I'm scared shitless of a) pulling my car apart to install them and b) baking the headlights. It sorta feels like..i dunno...holding live birds underwater to see if they can swim...
Image

User avatar
blanka
INACTIVE Member Account
Posts: 822
Joined: Wed Sep 03, 2008 9:47 pm
Location: Cairns, QLD, Australia

Postby blanka » Wed Mar 25, 2009 4:27 pm

Josh_Emerton wrote:They look great Zeb

I'd do it myself but I'm scared shitless of a) pulling my car apart to install them and b) baking the headlights. It sorta feels like..i dunno...holding live birds underwater to see if they can swim...


ahahaahah pulling the car apart is pretty easy but yeh i was pretty scared of the baking part


Return to “Lighting”

Who is online

Users browsing this forum: No registered users and 58 guests