***** ALERT - Nominations for your new ClubCJ Committee can be made here *****

El wire

HID's, Bulb's + LED Interior and Exterior Illumination.

Moderators: Moderators, Senior Moderators

User avatar
Dirtee
Lancer Legend
Lancer Legend
Posts: 1297
Joined: Mon Sep 26, 2011 8:31 pm
Location: Canberra, Australia
Contact:

Postby Dirtee » Tue Feb 07, 2012 9:23 pm

get them around your subs bro!
2010 Lancer Es - My Ride
Wanna be customiser!!
ACT Rep 2012
CJLancerInstalls - How-To's!

User avatar
T-All3NT
Lancer VRX/GTS
Lancer VRX/GTS
Posts: 301
Joined: Wed Dec 21, 2011 8:51 pm
Location: Canberra, Australia

Postby T-All3NT » Tue Feb 07, 2012 9:26 pm

That's what some of the wire is going to be used for (possibly), but then I got the other half of the el to use

User avatar
Dirtee
Lancer Legend
Lancer Legend
Posts: 1297
Joined: Mon Sep 26, 2011 8:31 pm
Location: Canberra, Australia
Contact:

Postby Dirtee » Tue Feb 07, 2012 9:32 pm

just light the crap out of the boot ;)
2010 Lancer Es - My Ride

Wanna be customiser!!

ACT Rep 2012

CJLancerInstalls - How-To's!

User avatar
T-All3NT
Lancer VRX/GTS
Lancer VRX/GTS
Posts: 301
Joined: Wed Dec 21, 2011 8:51 pm
Location: Canberra, Australia

Postby T-All3NT » Tue Feb 07, 2012 9:41 pm

haha i might, but its already heaps bright from the 2x 12" leds in the trunk

User avatar
BRE88N
Lancer ES/EX
Lancer ES/EX
Posts: 180
Joined: Mon Aug 08, 2011 9:12 pm
Location: nsw sydney

Postby BRE88N » Tue Feb 07, 2012 9:41 pm

where abouts are u thinking about putting them

User avatar
T-All3NT
Lancer VRX/GTS
Lancer VRX/GTS
Posts: 301
Joined: Wed Dec 21, 2011 8:51 pm
Location: Canberra, Australia

Postby T-All3NT » Tue Feb 07, 2012 9:43 pm

BRE88N wrote:where abouts are u thinking about putting them

well not 100% sure haha, i don't wanna do the interior unless i put a switch on it, so i don't get a defect
but im gonna get them and then find a place for them

User avatar
nava1990
Lancer Newbie
Lancer Newbie
Posts: 80
Joined: Sat Jul 30, 2011 9:48 am
Location: Sydney

Postby nava1990 » Tue Feb 07, 2012 11:53 pm

man you know what, if you could put them behind where the hazard lights are on. just below the stereo. if you were to pull that thing off and run it inside there.

iv seen an evo have it and it lights up through bottom part of it.

i dont know if im making sense, but man that would look ssssssiiiiiiiiiccccccccccccccccccckkkkkkkkkkkk

LIKEEE Below!!

Image

User avatar
nava1990
Lancer Newbie
Lancer Newbie
Posts: 80
Joined: Sat Jul 30, 2011 9:48 am
Location: Sydney

Postby nava1990 » Tue Feb 07, 2012 11:54 pm

aite screw that im buying one in red rite now.

User avatar
JaZira5
Lancer VR/GT
Lancer VR/GT
Posts: 213
Joined: Sat Mar 12, 2011 3:03 am
Location: Hawthorne, Queensland, Australia

Postby JaZira5 » Fri Feb 10, 2012 3:23 am

@nava1990: That's exactly I was thinking of when I saw this. To buy a few of them and line the front dash and doors. It would look good. To think OEM it would cost close to a grand or more to get replacement dash parts for this look. Though, question is how to line the dash with it, without the cable bulging out and keeping it falling off from the heat.

Keep us all updated how it goes. I would be very interested your installation process to making your dash look like that. ^_^


Return to “Lighting”

Who is online

Users browsing this forum: No registered users and 15 guests