***** ALERT - Nominations for your new ClubCJ Committee can be made here *****

Angel Eyes?

HID's, Bulb's + LED Interior and Exterior Illumination.

Moderators: Moderators, Senior Moderators

Post Reply
User avatar
jerryme
Lancer VRX/GTS
Lancer VRX/GTS
Posts: 365
Joined: Wed Nov 03, 2010 10:37 am
Location: Brisbane, Australia

Postby jerryme » Tue Feb 08, 2011 10:09 am

BR14AN wrote:
jerryme wrote:I bought these today. http://cgi.ebay.com.au/Lancer-Angel-Eye ... 500wt_1156

Can't wait to get them installed!


Whats the install process? Do the headlights still need to be baked?


To be honest I'm not too sure. On the page it says it comes with instructions, yet professional installation needed. Will post up the results when it comes.
bd-850
Alumni
Alumni
Posts: 4486
Joined: Sat Apr 25, 2009 6:37 pm

Postby bd-850 » Tue Feb 08, 2011 10:14 am

i would say yes otherwise how will you get the rings inside the headlight
User avatar
LZY_EYE
Genius
Genius
Posts: 6382
Joined: Mon Jun 29, 2009 10:12 am
Location: Central Coast, NSW

Postby LZY_EYE » Tue Feb 08, 2011 10:14 am

You have to bake the headlights to break the seal. You then bake the pieces again to reseal.

Not sure what temperature etc you would use as I have never installed.
User avatar
PsyTrix
Lancer VRX/GTS
Lancer VRX/GTS
Posts: 341
Joined: Fri May 21, 2010 7:25 pm
Location: Perth

Postby PsyTrix » Tue Feb 08, 2011 11:07 am

Id just get it done at concord customs.. Atleast that way you know your getting good quality led rings and they are installed perfectly.
Ralliart/Evo parts Versus 20s and BBS rims for sale! see: http://clubcj.net/viewtopic.php?t=7346
munky88888
Lancer Learner
Lancer Learner
Posts: 8
Joined: Tue Dec 21, 2010 8:53 pm
Location: Sydney

Postby munky88888 » Tue Feb 08, 2011 1:23 pm

anyone know roughly how much it would cost to get it done at concord customs?
User avatar
ofey
Alumni
Alumni
Posts: 8582
Joined: Mon Oct 27, 2008 8:56 pm
Location: Melbourne, VIC, Australia
Contact:
Contact ofey

Postby ofey » Tue Feb 08, 2011 2:14 pm

Depends how much liability you will put on them. Say they F**K up the baking? Baking too long and the plastic starts to warp, it will cost them A$300+ to replace that side.

It's great if there's someone out there who can do these things but you must accept that it may not be a perfect job. It's not their car. It's a job.

I strongly suggest this is a DIY thing. It's literally bake till glue softens, put on the rings, clip back the lens melt glue reform seal, put back onto car. Patience is the key. You need a lot of time as you slowly increase the heat till the glue melts.
Beeble tooned MY08 OEd. w/ RA BKit+SWheel
Cosworth Panel Filter w/ RA Intake | SuperCircuit 4-2-1 Headers | Creat’d Ti-tipped SS exhaust
BC BR-type Coilovers | UR + Whiteline Bars
EBC GreenStuff Pads | RDA Rotors
User avatar
jerryme
Lancer VRX/GTS
Lancer VRX/GTS
Posts: 365
Joined: Wed Nov 03, 2010 10:37 am
Location: Brisbane, Australia

Postby jerryme » Mon Feb 14, 2011 5:22 pm

So me and a friend installed my angel eyes today. The kit I bought didn't include instructions so i found the ones by automoglow on this website. The rings weren't as big as the outline of the headlight, so they sit just inside the ring. I went to test the angel eyes and turns out one of the lowbeams had been broken.. So I'm driving with 3 angel eyes :P Contacted the seller just before to arrange a replacement. Pics will be up shortly. All in all, it was a success. I would recommend this mod to everyone. It looks great.
User avatar
jerryme
Lancer VRX/GTS
Lancer VRX/GTS
Posts: 365
Joined: Wed Nov 03, 2010 10:37 am
Location: Brisbane, Australia

Postby jerryme » Mon Feb 14, 2011 5:54 pm

Some picsImage
Last edited by jerryme on Tue Jun 07, 2011 10:45 am, edited 2 times in total.
User avatar
washman
Lancer ES/EX
Lancer ES/EX
Posts: 107
Joined: Fri Mar 11, 2011 7:55 pm
Location: Sydney

Postby washman » Tue Jun 07, 2011 10:21 am

has anyone purchased the automoglow angel eyes, if s o do u guys have any comments on them ?
User avatar
Glenn
Lancer Ralliart
Lancer Ralliart
Posts: 737
Joined: Fri Jan 21, 2011 9:54 am
Location: Brisbane Northside

Postby Glenn » Tue Jun 07, 2011 10:34 am

Yup. I got mine from automoglow and no issues. Pretty straightforward install although a bit time consuming.
n_aghdassi
Lancer ES/EX
Lancer ES/EX
Posts: 160
Joined: Mon Jun 13, 2011 9:11 pm
Location: Perth

Postby n_aghdassi » Thu Jun 23, 2011 3:31 am

anyone in perth wanna install mine for a few beers?
:P
Post Reply

Return to “Lighting”

Who is online

Users browsing this forum: No registered users and 5 guests