***** ALERT - Nominations for your new ClubCJ Committee can be made here *****

Delay for aftermarket reversing sensors

Alarms, Smart Key, Batteries, Wiring, Engine/Computer Management & Racing Chips.

Moderators: Moderators, Senior Moderators

User avatar
ash06
Lancer VRX/GTS
Lancer VRX/GTS
Posts: 396
Joined: Sun Dec 28, 2008 3:47 pm
Location: Sydney, NSW, Australia

Delay for aftermarket reversing sensors

Postby ash06 » Thu Jul 26, 2012 11:01 pm

I have a aftermarket reverse sensor kit installed, however it has been bugging me for quite some time that it kicks in instantly.

When switching from Drive to Park; while passing Reverse, the sensor will startup and die shortly after. So there are audible 'beeps' as it announces it's on. It seems it has enough time to power up quickly and die.

I would like to add a 1-2 second delay to the sensors, so that they only really activate when I am genuinely reversing.


I have installed the kit myself so I'm confident in installing a relay? of some sort but I'm unsure if thats the way to achieve this.


My was thinking is on the lines of maybe a product like this:

http://www.ebay.com.au/itm/MINI-SMD-TIM ... 702wt_1020


But am not 100% if this is designed to 'keep things on' or actually delay them from starting

Any help is appreciated

User avatar
Fitter
Club Vendor
Club Vendor
Posts: 1288
Joined: Mon Mar 29, 2010 1:34 pm
Location: Brisbane

Postby Fitter » Thu Jul 26, 2012 11:18 pm

It picks up the signal as soon as the reverse light turns on. Way around it is

Secondary switch. Input from reverse through switch and then output to sensor module.

You control when it turns on then.

Or use accessories instead of reverse so u can turn it on at any time.... Tailgaters or drivers getting right up your back end at lights etc
CLUB CJ CAR AUDIO VENDOR
Owner and Builder of Australia's LOUDEST STREET LEGAL Lancer 147.5dB

2013 WORLD TITLE
2012 QLD State Champion
2008 Australian Champion

Image

User avatar
ash06
Lancer VRX/GTS
Lancer VRX/GTS
Posts: 396
Joined: Sun Dec 28, 2008 3:47 pm
Location: Sydney, NSW, Australia

Postby ash06 » Fri Jul 27, 2012 1:40 am

Hey Fitter,

Yep I understand that,
I'm trying to see if there's a way to stop it powering up for 1-2 seconds when switching gears

I have the sensors wired to a relay using a 12V source as the power and reverse light as the relay trigger. (So it's not to pull too much power from reverse lights as I already have a reverse camera hooked up to it)

I don't want to have a switch to control these as I'd rather a somewhat 'automatic' activation when reversing

Would the eBay item work?

In the item description it says:

"Principe of work:

When power is on, the relay is activated:
/normally open contact (Ob and Not) is closed and normally closed contact (Ob and Nzat) is open/ and keep that position, until end of set time.
By restart power supply - cycle repeat.
Device don't have plastic box, only plate, as see on the picture"

User avatar
Fitter
Club Vendor
Club Vendor
Posts: 1288
Joined: Mon Mar 29, 2010 1:34 pm
Location: Brisbane

Postby Fitter » Fri Jul 27, 2012 6:53 am

I can't see why it wouldn't work.

I like that 1 beep as u flick through the gears or enter reverse as it lets u know the kit is working still.

I do use a switch when doing front parking sensors instead of relying on the brake to turn them on... When ever u would hit the brake to stop or slow down in traffic u would get a 90dB high pitch tone through the car lol
CLUB CJ CAR AUDIO VENDOR

Owner and Builder of Australia's LOUDEST STREET LEGAL Lancer 147.5dB



2013 WORLD TITLE

2012 QLD State Champion
2008 Australian Champion


Image

User avatar
ash06
Lancer VRX/GTS
Lancer VRX/GTS
Posts: 396
Joined: Sun Dec 28, 2008 3:47 pm
Location: Sydney, NSW, Australia

Postby ash06 » Fri Jul 27, 2012 2:48 pm

Thanks Fitter,

I'll go ahead & purchase that item hopefully it works
I wouldn't mind 1 beep, but my kit beeps 3 times when starting up so it gets annoying when switching from gear to gear

I haven't thought about front sensors as yet but *am* interested in installing them in the future
I'd probably wire those to a switch as well
Like you said, it would be annoying to hear a **BEEP** every time you brake lol

Has anyone done a front sensor install for the CJ yet? I'm unsure of the mounting position & would I be looking at 2 or 4 sensors?


Ash

User avatar
Fitter
Club Vendor
Club Vendor
Posts: 1288
Joined: Mon Mar 29, 2010 1:34 pm
Location: Brisbane

Postby Fitter » Fri Jul 27, 2012 3:23 pm

4 is better but if it's just for guiding up onto a wall or another car in a carpark go 2

I can mock up my front bar take a photo for you
CLUB CJ CAR AUDIO VENDOR

Owner and Builder of Australia's LOUDEST STREET LEGAL Lancer 147.5dB



2013 WORLD TITLE

2012 QLD State Champion
2008 Australian Champion


Image


Return to “Electrical”

Who is online

Users browsing this forum: No registered users and 41 guests