***** ALERT - Nominations for your new ClubCJ Committee can be made here *****
Ralliart Exterior
Moderators: Moderators, Senior Moderators
Ralliart Exterior
Hey guys I have a Lancer 2010 ES and was looking to upgrade my exterior with ralliart bits from a wreckers. Has anyone done it before? Does it use the same clips and holes? so it can just be swapped? Or is extra modification required e.g. drill holes etc?
Last edited by NateIRL on Tue Jul 26, 2016 1:45 pm, edited 1 time in total.
Re: Ralliart Exterior
Extra medication?? Anyway, the RA exterior is mostly the same as that of the VRX, except the bonnet of course. You can buy the spoilers on-line or from members here who might be selling them, though you will usually have to get them resprayed to match your colour. MitsubishiParts.com is a good site to check, and if you look in the group-buy forum here you will find a thread where you can get them cheaper through Ofey, the chief buyer.
For example, here's the front spoiler/air-dam (in red, they have other colours, these ones are already painted though not sure how well the colours match).
For example, here's the front spoiler/air-dam (in red, they have other colours, these ones are already painted though not sure how well the colours match).
- Ronan.Butler11
- Lancer VRX/GTS
- Posts: 356
- Joined: Sun Apr 17, 2016 9:38 pm
- Location: Sydney, NSW, AUS
Re: Ralliart Exterior
^ thought i would give this a bump, would this still apply for the ralliart sportback and the VRX? looking at putting the RA rear bumper on my VRX so i can get a double exhaust. only aftermarket i found are $400+...
"When I Grow Up, I Wanna Be An Evo! (9 MR with a filthy BOV)
'09 Lancer VRX
Modifications:
De-Res Then a 2.5" Dual Exit X-Force Axle back Exhaust
18" King Rims
Ralliart Snorkel
LED No. Plate lights and interior
*insert further useless modifications to make it seem like i'm good at this*
'09 Lancer VRX
Modifications:
De-Res Then a 2.5" Dual Exit X-Force Axle back Exhaust
18" King Rims
Ralliart Snorkel
LED No. Plate lights and interior
*insert further useless modifications to make it seem like i'm good at this*
Re: Ralliart Exterior
I was actually somewhat mistaken, the RA front bumper, while similar, requires a lot of different parts such as different fog lights, different undertray, etc. As for the rear bumper, I'm not really too sure, I would imagine it would fit on the same and shouldn't have anything in the way. You can get some rear diffusers that don't replace the whole rear bumper, but I imagine you would have to cut your existing bumper to put those on.
Are you dead set on a dual exhaust? They look good, but it's going to be a lot more money and work than just getting a new single exit system installed.
Are you dead set on a dual exhaust? They look good, but it's going to be a lot more money and work than just getting a new single exit system installed.
- Ronan.Butler11
- Lancer VRX/GTS
- Posts: 356
- Joined: Sun Apr 17, 2016 9:38 pm
- Location: Sydney, NSW, AUS
Re: Ralliart Exterior
I'm pretty set on the dual exit, only going for an axle back so it isn't as pricey as i could be. i just feel the back end is letting the car down a bit, and love the look of dual exit. but like you said, the whole system is a bit pricey.
"When I Grow Up, I Wanna Be An Evo! (9 MR with a filthy BOV)
'09 Lancer VRX
Modifications:
De-Res Then a 2.5" Dual Exit X-Force Axle back Exhaust
18" King Rims
Ralliart Snorkel
LED No. Plate lights and interior
*insert further useless modifications to make it seem like i'm good at this*
'09 Lancer VRX
Modifications:
De-Res Then a 2.5" Dual Exit X-Force Axle back Exhaust
18" King Rims
Ralliart Snorkel
LED No. Plate lights and interior
*insert further useless modifications to make it seem like i'm good at this*
Re: Ralliart Exterior
Yeah, it certainly looks nice with dual exit. In that case, it's been done a few times by people here on the forums, with varying success in terms of the rear bumper/diffuser. Just use the search option and you shouldn't have any problems.
Here's one thread on the Mars Performance bumper.
Here's one thread on the Mars Performance bumper.
- Ronan.Butler11
- Lancer VRX/GTS
- Posts: 356
- Joined: Sun Apr 17, 2016 9:38 pm
- Location: Sydney, NSW, AUS
Re: Ralliart Exterior
better look nice once it's done hahaha, reckon i could grab a RA bumper from a wreckers? heard that Mitsubishi ask for a VIN to order it, would wreckers be the same? found an evo wrecker out at riverstone, rather know before i make that trek of a run hahaha
"When I Grow Up, I Wanna Be An Evo! (9 MR with a filthy BOV)
'09 Lancer VRX
Modifications:
De-Res Then a 2.5" Dual Exit X-Force Axle back Exhaust
18" King Rims
Ralliart Snorkel
LED No. Plate lights and interior
*insert further useless modifications to make it seem like i'm good at this*
'09 Lancer VRX
Modifications:
De-Res Then a 2.5" Dual Exit X-Force Axle back Exhaust
18" King Rims
Ralliart Snorkel
LED No. Plate lights and interior
*insert further useless modifications to make it seem like i'm good at this*
Re: Ralliart Exterior
If you like the dual exhaust look you are best to make one of them a dummy pipe otherwise it's makes it hard for tuning
Re: Ralliart Exterior
Would a heat shield be needed for a dual exit exhaust on MY12 + CJs?
Re: Ralliart Exterior
I don't imagine a wrecker would ask for a VIN haha, they don't care as long as they can sell the part
Re: Ralliart Exterior
sarusa wrote:Would a heat shield be needed for a dual exit exhaust on MY12 + CJs?
I highly doubt it but it depends how hot your exhaust gets and how close it is to the bumper
- Ronan.Butler11
- Lancer VRX/GTS
- Posts: 356
- Joined: Sun Apr 17, 2016 9:38 pm
- Location: Sydney, NSW, AUS
Re: Ralliart Exterior
aspir3 wrote:If you like the dual exhaust look you are best to make one of them a dummy pipe otherwise it's makes it hard for tuning
this is true... but i do a lot of early morning driving, makes it a bit obvious that one is a dummy hahahaha
"When I Grow Up, I Wanna Be An Evo! (9 MR with a filthy BOV)
'09 Lancer VRX
Modifications:
De-Res Then a 2.5" Dual Exit X-Force Axle back Exhaust
18" King Rims
Ralliart Snorkel
LED No. Plate lights and interior
*insert further useless modifications to make it seem like i'm good at this*
'09 Lancer VRX
Modifications:
De-Res Then a 2.5" Dual Exit X-Force Axle back Exhaust
18" King Rims
Ralliart Snorkel
LED No. Plate lights and interior
*insert further useless modifications to make it seem like i'm good at this*
- Ronan.Butler11
- Lancer VRX/GTS
- Posts: 356
- Joined: Sun Apr 17, 2016 9:38 pm
- Location: Sydney, NSW, AUS
Re: Ralliart Exterior
Skrallex wrote:I don't imagine a wrecker would ask for a VIN haha, they don't care as long as they can sell the part
Sweeeeeet
found an evo wreckers with a few RA, might check them out within the next few weeks
Thanks for your help bro
"When I Grow Up, I Wanna Be An Evo! (9 MR with a filthy BOV)
'09 Lancer VRX
Modifications:
De-Res Then a 2.5" Dual Exit X-Force Axle back Exhaust
18" King Rims
Ralliart Snorkel
LED No. Plate lights and interior
*insert further useless modifications to make it seem like i'm good at this*
'09 Lancer VRX
Modifications:
De-Res Then a 2.5" Dual Exit X-Force Axle back Exhaust
18" King Rims
Ralliart Snorkel
LED No. Plate lights and interior
*insert further useless modifications to make it seem like i'm good at this*
- lancer-noob
- Lancer Newbie
- Posts: 33
- Joined: Thu Feb 25, 2016 1:46 pm
- Location: VIC
Re: Ralliart Exterior
Ronan.Butler11 wrote:found an evo wreckers with a few RA,
Where did you find them? I am interested to get a RA or Evo hook.
- lancerdarryl
- Lancer MASTER
- Posts: 1929
- Joined: Wed Jul 14, 2010 3:10 am
- Location: Newcastle NSW Australia
Re: Ralliart Exterior
Hook or hood?
Evolution X MR+ Lancer VRX Sportback +LA Lancer GSR
"Don't back off until you hit something"
"Don't back off until you hit something"
Who is online
Users browsing this forum: No registered users and 23 guests