***** ALERT - Nominations for your new ClubCJ Committee can be made here *****

I bought an Evo8/9 Replica Wing.....

Exterior Parts/Accessories & Modifications.

Moderators: Moderators, Senior Moderators

Post Reply
User avatar
poe_sniper
Lancer VR/GT
Lancer VR/GT
Posts: 291
Joined: Mon Jan 30, 2012 4:30 pm
Location: Glen Oak

I bought an Evo8/9 Replica Wing.....

Postby poe_sniper » Sun Jul 29, 2012 9:57 am

Hi Guys

Well as the topic suggests I bought a Replica Evo 8/9 Wing. I'm going to put it on my WW Ralliart like this:
http://www.torontomazda3.ca/forum/showthread.php?45933-Mitsubishi-Lancer-Ralliart-Mini-Photoshoot&highlight=ralliart

From what I've read when you put a new wing on you put down a sticky seal type thing???
Where do I purchase some of that stuff from?

Any ideas/help is appreciated.

Thanks
Jarryd
bd-850
Alumni
Alumni
Posts: 4486
Joined: Sat Apr 25, 2009 6:37 pm

Postby bd-850 » Sun Jul 29, 2012 10:15 am

i used double side tape, if the wing doesnt come with any
User avatar
poe_sniper
Lancer VR/GT
Lancer VR/GT
Posts: 291
Joined: Mon Jan 30, 2012 4:30 pm
Location: Glen Oak

Postby poe_sniper » Sun Jul 29, 2012 12:06 pm

The wing hasn't come with any. Is it really that simple?
Image
User avatar
lancerdarryl
Lancer MASTER
Lancer MASTER
Posts: 1929
Joined: Wed Jul 14, 2010 3:10 am
Location: Newcastle NSW Australia

Postby lancerdarryl » Sun Jul 29, 2012 2:49 pm

poe_sniper wrote:The wing hasnt come with any. Is it really that simple?

Yep............ ...how about a photo or two when you fit it?
Evolution X MR+ Lancer VRX Sportback +LA Lancer GSR
"Don't back off until you hit something"
User avatar
poe_sniper
Lancer VR/GT
Lancer VR/GT
Posts: 291
Joined: Mon Jan 30, 2012 4:30 pm
Location: Glen Oak

Postby poe_sniper » Sun Jul 29, 2012 3:09 pm

There will certainly be a few photos posted. :-)
User avatar
poe_sniper
Lancer VR/GT
Lancer VR/GT
Posts: 291
Joined: Mon Jan 30, 2012 4:30 pm
Location: Glen Oak

Postby poe_sniper » Sun Aug 05, 2012 7:57 pm

I put it on today. Here are some pics. Took a bit of work, but I love it :-).
Image

Image

Image
User avatar
Syke
Lancer VR/GT
Lancer VR/GT
Posts: 291
Joined: Mon Jun 11, 2012 10:24 am
Location: Toowoomba, Australia

Postby Syke » Sun Aug 05, 2012 8:21 pm

that looks really good
Syke
One step closer to owning an Evo

Google Is Your Friend! Learn to embrace it...
Check Out My Garage
http://clubcj.net/garage.php?mode=view_vehicle&CID=1054
User avatar
sleeper
Alumni
Alumni
Posts: 8259
Joined: Fri Apr 23, 2010 10:14 am
Location: brisbane
Contact:
Contact sleeper

Postby sleeper » Sun Aug 05, 2012 8:35 pm

looks great Jarryd
210 KWATW 400nm RALLIART Virtual Dyno 1/1
http://goo.gl/GrUosm


Image
User avatar
Momengah
Lancer Ralliart
Lancer Ralliart
Posts: 714
Joined: Mon Nov 22, 2010 9:59 pm
Location: Melbourne, Australia

Postby Momengah » Sun Aug 05, 2012 11:56 pm

hey awesome!!! that looks pretty good. Did you end up just tapping it on or put some screws in? need to drill any new holes?
-Beeble spec custom tune (182kw 383nm)
-Cosworth Air Filter
-Evo X BOV
-Evo X Intercooler
-Grimmspeed 3 port
-Ultimate Racing UPICP & LICP
-HFC & Ultimate Racing catback
User avatar
poe_sniper
Lancer VR/GT
Lancer VR/GT
Posts: 291
Joined: Mon Jan 30, 2012 4:30 pm
Location: Glen Oak

Postby poe_sniper » Mon Aug 06, 2012 7:50 am

Momengah wrote:hey awesome!!! that looks pretty good. Did you end up just tapping it on or put some screws in? need to drill any new holes?


The install took a bit of time but it was nothing too serious. The evo 9 spoiler mounts with two holes. The hole towards the rear of the car lines up perfectly, the other does not. But I figured the spoiler is way easier to replace than the boot so i decided to drill two new holes in each side of the spoiler. One where the old spoiler mounted and then in the side of the upright as an inspection hole. The inspection hole allowed me to put a nut on the bolt. I could do that as the carbon fibre insert on the side of the spoiler comes off and thus is hiding the hole :-).

Thanks
Jarryd
User avatar
zedd82
Lancer Evolution
Lancer Evolution
Posts: 892
Joined: Tue May 12, 2009 11:13 am
Location: Brisbane, QLD, Australia

Postby zedd82 » Mon Aug 06, 2012 2:22 pm

Looks really good.

Does it block much of your vision in the rear view mirror?
Club CJ's fastest and most powerful Ralliart 349.8kw/ 469hp atw 12.068s 187km/h
WhiteRA
Lancer Learner
Lancer Learner
Posts: 9
Joined: Thu Sep 16, 2010 12:19 am
Location: Brisbane, Australia

Postby WhiteRA » Mon Aug 06, 2012 2:45 pm

Looks great mate
User avatar
poe_sniper
Lancer VR/GT
Lancer VR/GT
Posts: 291
Joined: Mon Jan 30, 2012 4:30 pm
Location: Glen Oak

Postby poe_sniper » Mon Aug 06, 2012 5:55 pm

zedd82 wrote:Looks really good. Does it block much of your vision in the rear view mirror?


I believe there is more vision than before with the VRX spoiler.
Image
User avatar
The X
INACTIVE Member Account
Posts: 6769
Joined: Mon Aug 31, 2009 10:41 am
Location: Pyrmonia! Inner Sydney.
Contact:
Contact The X

Postby The X » Mon Aug 06, 2012 8:16 pm

That wing is ORSM! :D
Tho, I'd say that as I got one in blue.
I guess good looks are contagious. :P

Some call it a shopping trolley, but they're just hatin' :)
"the quieter you become, the more you are able to hear"
More pix @ http://clubcj.net/viewtopic.php?t=8779
ImageImage
User avatar
Momengah
Lancer Ralliart
Lancer Ralliart
Posts: 714
Joined: Mon Nov 22, 2010 9:59 pm
Location: Melbourne, Australia

Postby Momengah » Mon Aug 06, 2012 8:31 pm

is any Evo 9 replica wing going to work? Should I eBay it? I wanna get one too :P
-Beeble spec custom tune (182kw 383nm)

-Cosworth Air Filter

-Evo X BOV

-Evo X Intercooler

-Grimmspeed 3 port

-Ultimate Racing UPICP & LICP

-HFC & Ultimate Racing catback
Post Reply

Return to “Exterior”

Who is online

Users browsing this forum: No registered users and 64 guests