***** ALERT - Nominations for your new ClubCJ Committee can be made here *****

Another new Central Coastie.

Please Introduce Yourself Here.

Moderators: Moderators, Senior Moderators

User avatar
christiano
INACTIVE Member Account
Posts: 4
Joined: Sun Jan 24, 2010 9:10 am
Location: Central Coast NSW

Another new Central Coastie.

Postby christiano » Sun Jan 24, 2010 9:25 am

Hi Guys,
Another new member from the Central Coast.
I have a MARCH 2008 VRX Lancer with the Rockford upgrade.

I'm looking for instructions/diagrams/workshop manual to dismantle the dash above the steering wheel. I've done this on numerous cars before and would give it a go, but have learnt that unless you know the direction and location of the clips you can do damage.
I am wanting to install my Tom Tom power cable permanently in behind the dash so I don't have the cable dangling around...

Thanks
Christian
2008 VRX Lancer, Black , Manual, Rockford upgrade

User avatar
aspir3
Site Admin
Site Admin
Posts: 8415
Joined: Tue Oct 27, 2009 6:15 pm
Location: adelaide

Postby aspir3 » Sun Jan 24, 2010 9:36 am

Welcome Christian. You have come to right place for help.

I have seen a few discussions on your questions. I don't know where they are ex actually, but if you try the search at the top right of home page it will help.

If you cant find them I am sure SIR-VRX (Adrian) will be able to help as he is the clubs chief technician.

Lucky for you he is a Queensland er.

Good luck and post some pictures of your car and let us know how your mods go.

SIR-VRX
Genius
Genius
Posts: 7244
Joined: Mon Oct 06, 2008 11:16 pm
Location: Brisbane, QLD, Australia

Postby SIR-VRX » Sun Jan 24, 2010 1:41 pm

The workshop manual doesn't really show too much in the way of details directions, but I can give you a run down. I can take some pictures for you today, if required. I need to do it anyway one day, so might make it today if you need pictures.

1. Remove Glovebox and little side panel next to it. Open glovebox, unclip strut on the left side, then squeeze the sides of the glovebox in and lower it. Undo screw in little side panel.

2. Remove Dash garnish strip and radio fascia. Screw in dash garnish on left side, pull away from dash.

3. Remove lower panel below steering wheel. 2 screws and 3 push-clips on lower edge. Pull from the bottom, outwards.

4. Remove dash garnish to the right of the steering wheel. Undo screw and pull off.

5. Should be able to see now how the instrument fascia panel is clipped. pull from the bottom but not too far as you need to unplug the info switch wire.

6. If required, you can also take off the top scalloped panel now.

Hope that helps :)

SIR-VRX
Genius
Genius
Posts: 7244
Joined: Mon Oct 06, 2008 11:16 pm
Location: Brisbane, QLD, Australia

Postby SIR-VRX » Sun Jan 24, 2010 1:47 pm

Oh and in reference to your chat post

Light Green is Positive

Black is Negative

User avatar
LZY_EYE
Genius
Genius
Posts: 6382
Joined: Mon Jun 29, 2009 10:12 am
Location: Central Coast, NSW

Postby LZY_EYE » Sun Jan 24, 2010 2:19 pm

Welcome to the club :)

I have been thinking of doing the same thing with my gps too! Will get around to it one day...

User avatar
christiano
INACTIVE Member Account
Posts: 4
Joined: Sun Jan 24, 2010 9:10 am
Location: Central Coast NSW

Postby christiano » Sun Jan 24, 2010 2:33 pm

SIR-VRX wrote:The workshop manual doesn't really show too much in the way of details directions, but I can give you a run down. I can take some pictures for you today, if required. I need to do it anyway one day, so might make it today if you need pictures.

1. Remove Glovebox and little side panel next to it. Open glovebox, unclip strut on the left side, then squeeze the sides of the glovebox in and lower it. Undo screw in little side panel.

2. Remove Dash garnish strip and radio fascia. Screw in dash garnish on left side, pull away from dash.

3. Remove lower panel below steering wheel. 2 screws and 3 push-clips on lower edge. Pull from the bottom, outwards.

4. Remove dash garnish to the right of the steering wheel. Undo screw and pull off.

5. Should be able to see now how the instrument fascia panel is clipped. pull from the bottom but not too far as you need to unplug the info switch wire.

6. If required, you can also take off the top scalloped panel now.

Hope that helps :)



Thanks heaps for the info, I didn't destroy my car LOL

I have managed to remove absolutely everything except the upper dash above the intrument display.
I need to access the area above the A/C vents at the base of the A Pillar.
Seems to be a difficult area to get to, have been searching the forum and the web without luck.
It appears to be one large plastic fascia, can't make it budge without forcing, appears to be clipped (have removed 2 bolts and 1 screw from it and as a result the right side moves freely but it is well fixed on the left)[/img][list=][/list]
2008 VRX Lancer, Black , Manual, Rockford upgrade

SIR-VRX
Genius
Genius
Posts: 7244
Joined: Mon Oct 06, 2008 11:16 pm
Location: Brisbane, QLD, Australia

Postby SIR-VRX » Sun Jan 24, 2010 4:03 pm

I ran my GPS cable up the side panel on the dash (behind where the door shuts up against the dash) and it pops out of the rubber seal there ;)

Can take pics if you wish

User avatar
driftnut((
Lancer Evolution
Lancer Evolution
Posts: 950
Joined: Sun Oct 11, 2009 12:05 pm
Location: central coast Australia

Postby driftnut(( » Sun Jan 24, 2010 6:02 pm

hey christian welcome mate i think i may have refered u to this site goos 2 see u joined up
Image

driftnut((.. ClubCJ's first RX TURBO, Merlinised, K&N pod 18" KING wheels, BC coil overs, Alpine/Pioneer system, Short shifter, Cat back system, Evo x turbo system, ralliart injectors & pump

hotlanc
Lancer ES/EX
Lancer ES/EX
Posts: 148
Joined: Sat Jun 27, 2009 12:52 am
Location: Gold Coast

Postby hotlanc » Mon Jan 25, 2010 10:09 pm

Welcome to ClubCJ
Image
Wicked White MY10 Mitsubishi Lancer VRX


Return to “NEW MEMBERS”

Who is online

Users browsing this forum: No registered users and 33 guests