This is what the other connector looks like, it's near the hood opening mechanism, and fits perfectly; but once it's connected it gives the "Close Hood" warning when starting the car.
***** ALERT - Nominations for your new ClubCJ Committee can be made here *****
Search found 9 matches
- Tue Jul 15, 2014 12:45 pm
- Forum: Electrical
- Topic: OEM Fog Lights Install -- Problem afterwards! Need Help
- Replies: 14
- Views: 15699
- Tue Jul 15, 2014 12:42 pm
- Forum: Electrical
- Topic: OEM Fog Lights Install -- Problem afterwards! Need Help
- Replies: 14
- Views: 15699
This is a picture of the Fog Light power connector. http://i57.tinypic.com/x4py4l.jpg This is a picture of the plug where I think it should connect but it doesn't fit: http://i60.tinypic.com/31622rs.jpg (Hard to see, it's 1/3 down the radiator and closer to front, but it's definitely different and w...
- Tue Jul 15, 2014 9:27 am
- Forum: Electrical
- Topic: OEM Fog Lights Install -- Problem afterwards! Need Help
- Replies: 14
- Views: 15699
CVT. There were two unused plugs. 1 near the hood opening mech, which based on the above, I think might be for an alarm, and another half way down the radiator as you said. I tried the one near the hood, which is probably what is causing the problem; as the one near the rad certainly matches up with...
- Mon Jul 14, 2014 7:28 pm
- Forum: Electrical
- Topic: OEM Fog Lights Install -- Problem afterwards! Need Help
- Replies: 14
- Views: 15699
- Mon Jul 14, 2014 7:23 pm
- Forum: Electrical
- Topic: OEM Fog Lights Install -- Problem afterwards! Need Help
- Replies: 14
- Views: 15699
Yeah, same instructions. I didn't remove the front bumper (Only had a 2 hours to do the install, and I was too lazy), instead I just routed as best I could and skipped the part with Clamps for near the radiator (instead I went around the other side so the cable was safe and well clear of it, then ta...
- Mon Jul 14, 2014 6:50 pm
- Forum: Electrical
- Topic: OEM Fog Lights Install -- Problem afterwards! Need Help
- Replies: 14
- Views: 15699
Ok, so I've gone to have another look at it tonight. I tried Unpluging the 2-pin power connector in the front-centre from the Fog Light power connector and the problem goes away. As soon as I reconnected it, it came back. Did not take the Front Bumper Off, I took the front plastic cover along the fr...
- Mon Jul 14, 2014 6:08 pm
- Forum: Electrical
- Topic: OEM Fog Lights Install -- Problem afterwards! Need Help
- Replies: 14
- Views: 15699
At least that helps me to know somethings gone wrong, I'm really not 100% sure it's an electrical problem, ie maybe something interfering with sensor but the bonnet is physically fully shut, nothing obstructing it or even making it slightly ajar. Tonight I'll take out the relay and disconnect the po...
- Mon Jul 14, 2014 5:48 pm
- Forum: Electrical
- Topic: OEM Fog Lights Install -- Problem afterwards! Need Help
- Replies: 14
- Views: 15699
OEM Fog Lights Install -- Problem afterwards! Need Help
I've almost completed the installation of OEM Fog Lights (not eBay one, but genuine Mitsubishi ones), however since I do not have access to a Multi-Use Tester III (MUT-3), I haven't finished the activation and validation and they do not work yet. Also, I seem to have created another problem in that ...
- Mon Jul 14, 2014 5:39 pm
- Forum: NEW MEMBERS
- Topic: Hi from Steve in Canberra - CJ LX Sedan MY13
- Replies: 12
- Views: 10515
Hi from Steve in Canberra - CJ LX Sedan MY13
Real first name: Steve Location: Canberra ACT Model: Lancer CJ LX Sedan MY13 Colour: Black General interests: Farming, Cars + Motorbikes Current mods: OEM Fog lights (pending MUT3 activation), OEM Bonnet and Headlight protectors, OEM Boot Scruffplate, Exhaust Tip, Dash Cam, K&N Oil filter, Custo...